Patch-ID# 119239-01 Keywords: sun fire v210/v240 netra 240 Synopsis: Hardware/PROM: Sun Fire V210/V240 Netra 240 Flash PROM Update Date: Jun/10/2005 Install Requirements: Additional instructions may be listed below Solaris Release: 8 9 10 SunOS Release: 5.8 5.9 5.10 Unbundled Product: Hardware|PROM Unbundled Release: OBP 4.16.6,POST 4.16.5,OBDIAG 4.16.6 Xref: Topic: Relevant Architectures: sparc NOTE: sun fire v210/v240 netra 240 BugId's fixed with this patch: 5059929 5071186 6206112 6211546 6216781 6217930 6219577 6220285 6220303 6231224 6235884 6243243 6247508 6247511 6255271 Changes incorporated in this version: 6243243 6206112 6231224 6235884 6247508 6247511 6255271 5059929 6211546 6219577 Patches accumulated and obsoleted by this patch: Patches which conflict with this patch: Patches required with this patch: Obsoleted by: Files included with this patch: README.119239-01, copyright, 802-3233-25.ps flash-update-SunFire240-latest flash-update-SunFire240-old, unix.flash-update.SunFire240.sh, 817-6957-10.pdf, unix.flash-update.README, Problem Description: 5071186 Serial console doesn't work after reset-all. 6216781 Failed boot with Missing cmn-xxx[ error and Out of memory then FATAL: no exception frames available 6217930 V240 - FATAL: no exception frames available, forcing misaligned trap 6220285 Enws Enws_plus Taco Taco_Plus Banner Copyright need to be updated to year 2005 6220303 ENWS banner included "Sun Fire V250" that need to be removed. 6243243 OBP hangs on E25K after enable-reentry failure 6206112 obp 4.16.1 fails DVD test without DVD is installed 6231224 system hang up when enter ":c" to leave kadb prompt and get back into UNIX mode. 6235884 "NESTED ERRORs, going interactive forcing misaligned trap" seen after probing devices 6247508 system-tick-speed and the alarm interval need to be updated to correct value 6247511 support reentrancy in the memory list management 6255271 Latest (March 05) release of ENxS and Netra 210/240 motherboad not supported by latest obp. 5059929 ERROR: Timeout on 0:0 waiting for resource type 16. 6211546 POST fatals when OBP invokes the POST JTAG/Init sequence 6219577 find openboot.bin Patch Installation Instructions: ============================== Intro ----- This README is intended for users who wish to upgrade the firmware in their Sun Fire V210/V240,Netra 240. Summary of the Patch Installation Process: ------------------------------------------ The installation shall comprise of the following steps 1) Determine the system's current Flash PROM firmware revision. 2) Compare the current Flash PROM firmware revision with the available or latest Flash PROM firmware revisions. 3) If the current Flash PROM firmware revision is lower than the latest available firmware revision in this patch, then proceed to the next step. If NOT, STOP: DO NOT CONTINUE. 4) Prepare the system for the Flash PROM update 5) Running the Flash PROM Utility 6) Verifying successful Flash PROM Update 7) Restoring the system 8) Resume operations Patch Installation instructions (in detail): ============================================ The required steps are explained in greater detail below. 1) Determine the System's Current Firmware Revisions ------------------------------------------------- While the OS is running the following command may be used to determine the current system firmware revisions; /usr/sbin/prtconf -V or /usr/platform/sun4u/sbin/prtdiag -v | grep OBP The firmware revisions may also be determined from the PROM monitor's "ok" prompt with the following command; .version 2) Compare the current Flash PROM firmware revision with the available or latest Flash PROM firmware revisions. Compare the output of the OBP line in the "prtdiag -v" or "prtconf -V" output. Find the revision number and compare with the revision on the entries below that of the "flash-update-SunFire240-latest" line Available Firmware Revisions ---------------------------- flash-update-SunFire240-latest: OBP 4.16.6 2005/05/09 13:03 Sun Fire V210/V240,Netra 240 OBDIAG 4.16.6 2005/05/09 13:05 Sun Fire[TM] V210/V240,Netra[TM] 240 POST 4.16.5 2005/02/28 16:33 flash-update-SunFire240-old: OBP 4.16.4 2004/12/18 05:20 Sun Fire V210/V240,Netra 240 OBDIAG 4.16.4 2004/12/18 05:21 Sun Fire[TM] V210/V240,Netra[TM] 240 POST 4.16.3 2004/11/05 20:12 3) Is the UPGRADE NECESSARY? If the current Flash PROM revision matches the version numbers given under the flash-update-SunFire240-latest line, then STOP Here. This UPGRADE IS NOT NECESSARY. If the current Flash PROM firmware revision is lower than the latest firmware revision in this patch, then proceed to the next step. 4) Preparing the System --------------------- a) As root, copy the latest "flash-update" files from the directory containing the patch to the root directory as follows: # cp flash*latest / # chmod 755 /flash-update* In order to boot the binary, it must be located within the root partition. If it is not already located within the root partition then move it to /. If the binary is already located elsewhere within the root partition then note the exact filepath so that the binary can be booted later. b) As root, exit the OS such that the system returns to the PROM's "ok" prompt: # halt ok c) Jumper JP11 is factory-set so that the flash PROM is write-enabled. There is no need to switch the jumper before flash updating; however, you must ensure that the keyswitch is in the Power-on or Diagnostics position. When the key switch is in the locked position the flash PROM is write protected. 5) Running the Flash Update Utility -------------------------------- a) The system should now display the PROM monitor's "ok" prompt. Now boot the Flash update utility as given below: CAUTION: Do not boot/run revisions lower than the latest unless you are absolutely sure that that is what you want to do! ok boot disk /flash-update-SunFire240-latest NOTE: If your system's boot device is not "disk" then you will have to specify the appropriate devalias (e.g. disk2). If the binary is located in a location other than / then provide the entire filepath after the boot device. Answer the questions as prompted by the utility. +++++++++++++++++++++ example Flash update follows ++++++++++++++++++++++++ ++++++++ Note that this is an example only. Much of the information ++++++ ++++++++ which is displayed by your system will be different from ++++++ ++++++++ what is shown below. ++++++ +++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ Standalone Flash PROM Update Utility, Rev. 2.7 Ultra(tm) 1 Ultra(tm) 2 Ultra(tm) 5/10 Ultra(tm) 30 Ultra(tm) 60 / E220R Ultra(tm) 80 / E420R Ultra(tm) Enterprise(tm) 250 Ultra(tm) Enterprise(tm) 450 Sun Blade(tm) 100 Sun Blade(tm) 1000 Sun Fire (tm) 280R Netra(tm) T4 Sun Fire (tm) V880 Sun Fire (tm) V210/V240,Netra 240 This utility allows you to interactively update the firmware revisions in specific system Flash PROM components. Type h for help, q to quit, Return or Enter to continue: Every precaution should be taken to prevent the loss of system power during the Flash PROM programming process! Type h for help, q to quit, Return or Enter to continue: Firmware Release(s) Firmware Release(s) Currently Existing in the System Available for Installation / Install? ---------------------------------- ------------------------------------------- OBP 4.5.6 2002/01/04 12:30 OBP 4.6.3 2002/05/28 09:09 no POST 4.5.6 2002/01/04 15:54 POST 4.6.2 2002/05/21 10:41 no Type sa if you wish to select all available firmware releases for installation. Type h for help, quit to exit, or cont to continue: sa Firmware Release(s) Firmware Release(s) Currently Existing in the System Available for Installation / Install? ---------------------------------- ------------------------------------------- OBP 4.5.6 2002/01/04 12:30 OBP 4.6.3 2002/05/28 09:09 YES POST 4.5.6 2002/01/04 15:54 POST 4.6.2 2002/05/21 10:41 YES Type sa if you wish to select all available firmware releases for installation. Type h for help, quit to exit, or cont to continue: cont The Flash programming process is about to begin. Type h for help, q to quit, Return or Enter to continue: Erasing the top half of the Flash PROM. Programming OBP into the top half of the Flash PROM. Verifying OBP in the top half of the Flash PROM. Erasing the bottom half of the Flash PROM. Programming OBP into the bottom half of Flash PROM. Verifying OBP in the bottom half of the Flash PROM. Erasing the top half of the Flash PROM. Programming POST into the top half of Flash PROM. Verifying POST in the top half of the Flash PROM. Programming was successful. Resetting ... +++++++++++++++++++++ example Flash update ends ++++++++++++++++++++++++++ Once the PROM's banner reappears then use the Stop-A keys (or Break key, if running from a serial line) to abort the auto-boot sequence if the system begins to boot. 6) Verifying successful Flash PROM Update Verify from the results of the .version command that the OBP version matches the OBP version given above under the flash-update-SunFire240-latest entry in Step 2. 7) Resume operations a) Allow the system to auto-boot, or issue the boot command for your environment as necessary. b) Once the system has rebooted you may wish to remove the Flash Update binaries and documents since they will no longer be needed. # rm /flash-update* c) Remember to remove the files from their original location if they were not extracted directly into the root directory. *-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*- Special Install Instructions: ----------------------------- Note 1: This utility is *not* OS-dependent. The list of releases shown under the "Solaris Release" and "SunOS Release" sections may not be complete: The absence of a valid Solaris Release or SunOS Release from the lists above does not preclude the installation of this patch against the hardware. Note 2: This OBP upgrade requires that you have ALOM 1.2 or greater. If you do not have ALOM 1.2 or greater, you must upgrade your version of ALOM prior to upgrading your OBP. ALOM upgrades can be found at: http://www.sun.com/software/download/sys_admin.html or: http://www.sun.com/download and search for "Sun Advanced Lights Out Manager" If you install this patch without installing ALOM 1.2 then the MB Fault LED will light even though there is no fault Note that ALOM 1.2 has a dependency on Solaris 8 HW 7/03 or Solaris 9 8/03 or higher, due to BugId 4864535 which will result in prtdiag issues. Note 3: Modifications to Diagnostic Operation This released version of OpenBoot enables diagnostic execution for all power-on and error reset events, **as the new system default. **To implement this new policy, behavioral changes to diagnostic controls were made to simplify the enabling of diagnostics and controlling the level and verbosity of diagnostics. A new feature includes a Sun-prescribed mode of diagnostic execution, which overrides user-defined settings. This mode provides service personnel with an easy method by which to invoke a predictable execution of diagnostics. The new standard (default) configuration will increase system boot time ( measured from power-on to the 'ok>' prompt ) and messaging ( varies by system configuration ) for all 'power-on-reset' and OBP detected 'error-reset' events. Increased boot time and messaging is largely due to the execution of diagnostics. Automated System Recovery (ASR), a form of restoration, is implemented at the firmware layer and increases overall system availability when diagnostics are enabled. For more specific details regarding these OBP changes, reference the pdf document; "OpenBoot[tm] PROM Enhancements for Diagnostic ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** * PLEASE READ THE INSTRUCTIONS CAREFULLY AND ENTIRELY. PLEASE FOLLOW THE INSTRUCTIONS EXACTLY AS THEY ARE STATED. * FAILURE TO FOLLOW INSTRUCTIONS COULD EITHER RESULT IN A DEFECTIVE BOARD OR UNSUCCESSFUL FLASH PROM UPDATE. * THIS IS NOT A STANDARD PATCH in that it does not use the installpatch and backoutpatch scripts. * THIS PATCH CANNOT BE INSTALLED ON AN ONLINE OPERATING SYSTEM BECAUSE THE INSTALL INSTRUCTIONS REQUIRES THAT THE SYSTEM BE BROUGHT DOWN. BE SURE TO SCHEDULE DOWN TIME TO INSTALL THIS PATCH. * Installation of the firmware included with this patch does NOT require any hardware changes if the Flash update completes normally. * PLEASE REVIEW NOT ONLY THIS README BUT ALSO ADDITIONAL DOCUMENTATION GIVEN. The file "802-3233-xx.ps" (where xx stands for the latest numeric revision) is a PostScript copy of the "Sun Flash PROM Guide for Workstations and Workgroup Servers - Standalone Version", which provides the following; (i) Emergency instructions in the unlikely event that the Flash update should fail. Note, however, that The Programming Guide was originally written for a user who is running the Flash PROM update utility from a bootable CDROM, and thus it will not contain the proper boot commands for installation of this patch. Also note that the instructions in the document for installing packages are not valid for this patch. ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** README -- Last modified date: Friday, June 10, 2005